C4000
You can print the following Technical Data for COMBY 4000 from this website or if you would prefer to dowload these instructions as a word document click here

Technical data for COMBY 4000
Boiler in stainless steel
Boiler capacity 3Lt
Total power max 3.500W
Boiler power max 3.500W
Working pressure 800Kpa (8Bar)
Temperature max 176°C
Heating time 9 minutes
Suction power 1200W
Sound pressure 72,7dB (A)
Suction air 215sqm/hour
2 stages by-pass motor
Cold water tank 5Lt
Detergent tank 5Lt (only version with detergent)
Dirt bucket 7Lt
Weight 40Kg

Safety Devices
Thermostat 190°C
Thermostat with bulb 210°C automatic
Safety valve 13 bar
Electronic power balance
Teflon seals
Low voltage handle

Warning
ATTENTION
The manufacturer declines responsibility for damages deriving from using the appliance if:

  • The instructions of this manual are not respected

  • Modifications are brought in without previous authorisation from the manufacturer

  • Repairs are made by unauthorised persons

  • Parts of the appliance are replaced with not genuine parts

  • The machine is used differently from how it is recommended


  • The high pressure steam jet can be dangerous if it used in an improper way. Never direct the steam jet towards people.

  • Never direct the steam jet towards yourself or other people for cleaning clothes or shoes.

  • Do not use the appliance near other people, if they have not got protective clothing on.

  • Pay attention not to touch the nozzles, as these become very hot while using steam.

  • Never suck in flammable substances (petrol, solvents, varnish etc) Welding smoke, burning materials: danger of explosion & fire!

  • If the electrical cable is damaged, it has to be replaced immediately by the manufacturer or by an authorised person.

  • If an extension cable is used, plug & socket have to be watertight.

  • ATTENTION: A not adequate extension can be dangerous.

  • In case of leaks of foam or liquid, switch off immediately!

  • Children or not trained persons must not use the appliance.

  • To guarantee the safety of this appliance, only genuine spare parts have to be used.


  • Control Panel
    Do not pull at the steam hose, it could get damaged

    1. Main switch
    2. Boiler switch
    3. Detergent switch
    4. Steam output regulator
    5. Indicator light for power supply
    6. Indicator switch for lack of water
    7. Indicator light for steam ready
    8. Digital indicator of boiler temperature
    9. Pressure gauge
    10. Detergent tank cap (only version with detergent)
    11. Water tank cap
    12. Socket

    Instructions for use
    Preparation
  • Open the cap (11) and fill the cold water tank with tap water

  • Connect the plug to a socket on a patchboard provided with a switch with a efficient earth connection.


  • ATTENTION
    The appliance is provided with a power cord according to its electrical input characteristics. It`s important to verify that the electrical mains are according to the norms. It is recommended that the power supply of this appliance includes a differential switch of 30ma maximum.

    Starting (standard model)
  • For power supply, switch on the main switch 1.

  • The indicator light 5 goes on.

  • When the pump has filled up and the boiler goes out, switch on the boiler switch 2.

  • The appliance starts heating up (about 8 minutes comby 4000; 5minutes comby 9000).

  • The indicator light 7 goes on; the appliance is ready for use know.

  • Connect the steam hose to the socket 12, making sure that it is inserted correctly.

  • Push the steam button B on the handle and direct the steam jet towards the area which has to be cleaned.

  • For vacuum cleaning press the button for suction A on the handle.

  • The functions steam and vacuum can be used separately & also simultaneously


  • Starting (model with detergent injection)
  • Switch on the main switch 1, the indicator light 5 goes on.

  • Push switch 2 to switch on the boiler, the appliance starts heating up (about 8 minutes Comby 4000, Comby 9000 about 5 minutes)

  • The indicator light 7 goes on; the appliance is ready for use now.

  • Connect the steam hose to the socket 12, making sure that it is inserted correctly.

  • Push the steam button B on the handle and direct the steam jet towards the area which has to be cleaned.

  • For vacuum cleaning press the button for suction A on the handle.

  • If you want to use detergent, open the tap 10 and fill up the tank with detergent

  • The functions steam, steam & detergent can be used separately & also simultaneously


  • Attention
    Before starting steam cleaning, blow off the initial condensation in the conducts in a bucket or any other suitable place

    Vacuum Cleaning
    This appliance is not made to collect dangerous dust!
    For vacuum cleaning, first switch on the switch behind on the vacuum cleaner, then switch on the vacuum switch A on the handle. The vacuum system does not work when the switch on the vacuum cleaner is on position off!

    When the dirt bucket is full, the vacuum stops. Unhook the bucket, empty it, hook it again and then continue working.

    To clean the polyester filter unhook the bucket and take off the filter. Wash the filter and replace it, then hook the bucket.

    Detergent Injection - (only version with detergent)
    ATTENTION
    Do not use foaming or corrosive detergent, as this kind of detergent could damage the appliance!

    To switch on or off the detergent injection, push the switch 3 on the machine. When the detergent tank is empty, switch off switch 3, refill the tank with detergent, push switch 3 again & then you can continue working.

    Refilling Water
    When the cold water tank is empty you will hear an acoustic signal and the indicator light for lack of water 6 will go on. No steam comes out anymore.

    Proceed as follows:
    Open the cap 11 and fill the water tank
    Close cap 11
    After a few seconds the indicator light 8 will go on and you can continue cleaning.

    MAINTENANCE
    Always unplug the appliance before cleaning or servicing operations on the machine!

    For the safety of the operator and to secure always perfect performances, the following controls and servicing is recommended:

    After each use:
  • To clean the flexible hose and the used extension units, suck in a small quantity of clear water. Doing so you keep the conducts clean inside and prevent deposits and bad smells.


  • Unhook the dirt bucket, empty it and rinse it carefully


  • Periodically
  • Check regularly that the power cord does not present any signs of ware or ageing. If it is damaged it is absolutely necessary to replace it immediately by the same type of power cord, before using the appliance again.


  • Cleaning the boiler
    1. The machine has to cold and the electrical plug disconnected.
    Open the stopper under the machine and empty completely all remaining water in the boiler. When the boiler is empty close the stopper carefully but without exceeding.

    2. Control visually or with a rod the remaining water quantity in the cold water tank: for about 1Ltr water take 1Ltr vinegar (or a recommended de-scaler)

    3. Connect the electrical plug, switch on the main switch 1 (do not switch on the boiler switch 2) wait until the pump finishes to fill the boiler and goes out (it`s possible that the indicator light for lack of water 6 goes on and that you hear the acoustic signal) Switch off the main switch 1, disconnect the electrical plug and leave the machine for 8 hours.

    4. Empty the loose limestone in the solution and rinse the boiler proceeding as per point A.

    5. Fill the cold water tank with clean water and switch on the machine. For about 10 minutes use steam with care, because it will have a sharp smell because of the remaining vinegar in the boiler and in the conducts.

    6. When the operation boiler cleaning is completed, to start the appliance again follow the instructions explained under starting

    ATTENTION
    When the pump is filling the boiler, it`s recommended to control if the stopper under the machine is leaking

    Troubleshooting
    Anomaly
    Water is leaking from the accessories
    Solution
    Due to wear or damage of seals - Replace the seals on the coupling paying attention not to cut or to mark them and to place them carefully
    Anomaly
    Plug of the steam hose is difficult to insert in the socket of the machine
    Solution
    Do not force to insert it, but put a bit of silicone on the steam coupling in the machine
    Anomaly
    Boiler needs more time to heat up
    Solution
    Clean the boiler as explained
    Anomaly
    Pressure goes down quickly while using steam
    Solution
    Symptom of limestone, clean the boiler as explained

    ACCESSORIES
    The right steam hose and suitable accessories are important for the safety of this appliance. Therefore it is recommended to use only genuine steam hose & accessories.

    Standard Accessories
    1. Extension units
    2. Flexible hose with handle & plug
    3. Multipurpose brush
    4. Carpet protection for multipurpose brush
    5. Frame with bristles and ruber scrapers for multipurpose brush
    6. D60 nylon brush
    7. D26 nylon brush
    8. Steam lance
    9. D26 brass brush
    10. Large nozzle
    11. Small nozzle
    12. Glass cleaner

    Optional Accessories
    1.Upholstery tool
    2.Long steam lance
    3.Triangular brush
    4.Floor brush L=400
    5.Accessory with bristles L=400
    6.Accessory for liquids L=400
    7.Accessory for carpets L=400
    8.Floor brush L=300
    9.Accessory with bristles L=300
    10.Accessory for liquids L=300
    11.Accessory for carpets L=300
    12.Metallic floor brush L=370

    WARRANTY
    The manufacturer guarantees this appliance for a period of twelve months from the date of purchase against manufacturing blemish and defects in materials.

    Warranty Conditions
  • The warranty does not cover damages deriving from normal wear

  • The warranty does not cover damages or accidents due to non respect of the instructions of this manual, bad servicing or improper use of the appliance.

  • The warranty comprehends replacement and or repair of faulty parts, including workmanship. Under no circumstances the acknowledgement of the warranty involves an acknowledgement of damages or claims of any type or cause.

  • Transport and packing costs are the purchases charge.


  • Top of page

    Back


    Latest News
     

    Newsletter
    Please enter your email address below to receive our newsletter emails


    All content Copyright © Morclean Ltd 2008